Double Rotary Exchanger Aluminium 3-Way Mix (DRXA3MX)

Double Rotary Exchanger Aluminium 3-Way Mix (DRXA3MX)
ErP Logo

Air handling units incorporating thermal wheels and 3 way mix or air-mixing plenum are important elements in saving energy.

Heat Recovery Efficiency

The correct efficiency is a subjective decision and depends on the economic calculation and written guidelines, i.e. Ecodesign Commission Regulation (EU) No 1253/2014, on operating data such as energy prices, useful life, running times, temperatures, maintenance costs, and interest rates. With regard to (EU) No 1253/2014, profitability and environmental protection the heat recovery efficiency should be no less than 73%

Dependent on the right conditions heat recovery efficiencies can reach 90%

Air handling units incorporating plate heat exchangers and 3 way mix or air-mixing plenum are important elements in saving energy in Hotels, Corporate, High End Housing, Sports & Leisure, Education, Offices, Industrial, Data centre and Health.

This system works very well in buildings where the occupancy rate can vary greatly throughout the day, or seasonably. Additionally, when outside air conditions are such, typically mid-season weather conditions, it may be that ambient temperatures are suitable for free cooling purposes. In such conditions the mixing damper will set to close and the system uses full fresh air for optimum energy efficiency. Where fresh air is not required, such as early morning pre heat or pre conditioning periods, the mixing damper can be automatically set to full recirculation, again for optimum energy efficiency.

There is further added benefit of utilising a 3 Way Mix, such as frost coils are made redundant which saves costs in many areas including AHU coil, reduction in boiler and pump size, less pipe work and installation time on site.

Also no additional reheating or cooling capacity required for tempered air systems


Rotary heat exchanger air handlers are configured either in a side-by-side or stacked configuration. Rotary heat exchangers are classified as regenerators with rotating carrier. In a counter flow arrangement, the rotating, air permeable storage mass is heated and cooled alternately by heat releasing and heat absorbing air streams. Depending on the air conditions and on the surface of the storage mass also moisture may be transferred in this process. The supply and extract air streams must be adjacent and pass through the heat exchanger simultaneously.

From this process the specific heat output capacity depends on the temperature difference between the two air streams. Hence the rotary heat exchanger is suitable for heat as well as cool recovery, i.e. for winter and summer operation.

The AHU air-mixing plenum combines two air streams. The configuration includes three sets of dampers: one for the fresh air, one for the exhaust air, and a mixing damper between the two air streams. The mix of fresh air and recirculated air can thus be adjusted to suit the needs of the building's occupants. Typically as the fresh air and exhaust air dampers are driven from 0% open to 100% open, the mixing damper will in turn be driven from 100% open to 0% open, so as to always ensure a constant volume of supply and extract air.

As a general rule if in winter the internal total gains always exceed the fabric losses by 10% of the fresh air load then no mechanical heating is needed.

Ancillary Items

Air filtration is always present in order to provide clean dust-free air to the building occupants.

Direct heating, placed directly in the air stream, are direct heat exchangers and include those for gas-fired fuel-burning heaters or electric air heater batteries (EAHB). 

Indirect Heating and Cooling coils use hot water or steam for heating, and chilled water for cooling. Heat pumps can be used as well. (Prime energy for heating and cooling is provided by central plant).

Humidification is often necessary in colder climates where continuous heating will make the air drier, resulting in uncomfortable air quality and increased static electricity. Various types of humidification may be used as part of our air handler and include evaporative, vaporizer, spray mist and wetted medium.

If dehumidification is required, then the cooling coil is employed to over-cool so that the dew point is reached and condensation occurs. A heater coil placed after the cooling coil re-heats the air to the desired supply temperature and humidity level. This is often used for chilled beam applications. 

Smart Control System

Either our Smart Control System or the clients BMS may monitor return air quality, energy available to recover and CO2 concentration for optimum energy efficiency whilst maintaining desired fresh air requirements.


Our complete range of AHUs can be tailor made to suit all customer requirements including controls and refrigeration.

Air volume ranges from 0.4m3/s to 35m3/s.